Apiary

Production of frames for beehives with their hands.

Beekeeping zero – справа витратна, so many beekeepers tend to make their own hives and frames.

It's enough to have a minimum of experience and the necessary tools.

Actually, manufacturing frames for beehives with their hands performed quite simple.

The very frame is a rectangular frame, downed four doshechok.

Each of the rods is cut in a certain way. Of course, buy wooden bar quite expensive, so you can in a different way to cope with the task.

To make frames for beehives, You can use the door frame and old pieces of wood.

Обов’язкова умова – деревина повинна бути сухою. Before making necessary vidshkuryty well plates and remove them paint.

Then you cut each rail size, indicated in the drawings.

1. Production of frames for beehives 9 framework
2. Plans for beehives 12 framework
3. Beehive on the frame 145
4. 8-frame hive

Production of frames for beehives 9 framework

These hives Lanhstrota-called Ruta, they consist of 9 carcasses of Wax.

The size of this form of 470 on 300 mm.

To produce taken two side rails length 232 mm width 35 mm.

The top rail has a size 470 mm tall and 9 mm width.

The lower part width 19 mm and length 450 mm.

It is necessary not to forget, that statements in 1 cm made for, To properly set the frame in the hive.

pay attention, side rails have a rounded shape and unique performances, so for them using a special cutting machine.

Without such adaptations to make the frame very difficult, because we must consider space pidramochnyy.

pay attention, frames for rails must not contain knots. These places will always trickle resin, and during medosbora frame with honeycombs can just break at this point.

Therefore, without remorse throw boards with knots. Combines elements using shoe nails or staplers powerful construction with long straps.

Plans for beehives 12 framework

Such designs are different in size from the previous. In the hive two types of frames, one Shop, and other nest. They have a different location.

Frame store twice less, than breeding. The size of the shop napivramky 435 on 145 mm, а гніздової – 435 on 300 mm.

Composed frame, as in the first case, two identical side panels and different size front and rear rails.

The distance between frames in the hive will make 12 mm.

Beehive on the frame 145

Such houses for bees can easily be increased by adding adding soffit.

Перевага бджільництва в таких вуликах – скорочення праці бджоляра.

In this space each hive is not increased by adding frames, and by adding adding soffit.

Serve bee houses are easier, and they weigh much less.

The size of the frame 435 on 145 mm.

Very often experienced beekeepers hives used for such regular line of nail Wax.

It is, in such hive beekeeper intervenes at a minimum, and do all insects.

8-frame hive

Fabricate frames for houses of beer can in two sizes: width 230 or 300 mm. It all depends beehive design.

Such frames are no performances, Unlike framework for hives Dadana.

Instructions for manufacturing frames for beehives:

1. Cut the bars to the rails required size.
2. On the rails nails or a stapler.
3. Follow the four holes at equal distance from each other.
4. Pull the wire and secure it.
5. Pull the wire snake.
6. Pull the twine, to make it as a string, but the frame does not prohynavsya.
7. Secure the wire and tighten the end.

Now you can start navoschuvannya framework.

In commercially available plastic frame, they are very convenient and practical. But unfortunately, they can not be repaired after damage.

Among the advantages of low cost and lack of carcasses rotting. On the plastic does not grow mold and fungus.

The balance of these forms is carried out as usual.