Apiary

Multiple hives with their hands: construction, video.

The volume of the hive should match the size of the family and allow beekeepers to take measures to care for the nest, to further breeding bees.

In the evolution of bee nests high frame, most suitable for natural existence bdzholosim'yi, divided into several low.

Thus were created Multiple hives.

1. Multiple apiary: dignity
2. Multiple beehive frame with his hands
3. How to Make Multiple hive
4. Multiple beehives napivramku
5. Keeping bees in hives Multiple
6. Multiple beehive Foam

Multiple apiary: dignity

Multiple keeping bees allow beekeepers quickly carry out work in the apiary and serve more families.

• The main advantage of this technology keeping bees in the hive allowed Multiple simplify the maintenance of families, through the use of methods of work with the whole body at once.
• Multiple hives easily increased by adding the required number of shells, without which it can not do the apiary with abundant medosbora.
• Some additional elements Multiple hive allow for expansion slots for layering or swarm.
• If the damage Corps bees transferred to a nearby.
• Multiple hive versed, so it is easy to handle from bacterial diseases.
• The construction of the hive allows individual cases as hundreds of tanks during medosbora, and for frames after.

Multiple beehive frame with his hands

Multiple keeping bees has been used for over a century. These hives are five to seven shells.

Found another design: three buildings with four brood and store honey for Extension arm.

Multiple volume changes on, as many bees live in it and how much they collect nectar.

In the midst of this medosbora hive consists of 7 floors, and in the spring and during the winter the family enough for two buildings.

How to Make Multiple hive

In beekeeping are several technologies, How to Make Multiple hive with their hands.

• The body is a box, which has upper and lower end of shelters. Розміри корпусу – 450 mm * 375 mm * 240 mm wall thickness in 30 mm. In case concerns ten frame size 435 mm * 230 mm. In the case walls, retreating 70 mm from the top, cut holes for easy capture. The front wall of the eye under the pen prosverlyvaetsya, D = 25 mm. You can make eye schelovidni 8 mm * 60 mm.
• In two opposite walls of the housing grooves vypilivayutsya (17 mm * 11 mm) frame for hanging on the shoulders. Over framework remains little space for, not to damage the bees when installing casing or ceiling.
• Shop Extension arm. Її розміри – 450 mm * 375 mm * 155 mm. Nadstavtsi placed in store ten frame size 435 mm * 145 mm. Shop nadstavlyayut hives during medosbora. No eyes in stores.
• Frame. Розміри вуликів рамок багатокорпусного вулика – 435 mm * 230 mm. The frame consists of four bars of different thickness: to top 22 mm, bottom and two on the side 8 mm. The top bar nadstavlyayut hangers for hanging frames in the case. The upper part of the side bars of the frame thickness, lower than the bar (div. Drawing), therefore concluded beyond close. Of the two opposing sides in the frame on vysverdlyuyetsya 4 small holes for the wires (D = 0,5 mm) for the maintenance of cell loss. In store nadstavtsi make two of the same holes, like frame.
• Lattice resolution. Made of wire or plastic. With the help of the brood nest is separated from the honey Extension arm.
• The roof height 80 mm covered with iron and serves to protect the hive from the rain. For ventilation hive under the roofing cut the gap height 15 mm.
• The bottom of the hive is unilateral (placed below) and bilateral. Bilateral bottom floor and consists of bars size 570 mm * 65 mm * 35 mm on three sides. In the bars cut slit pazovaya (35 mm * 10 mm) to insert gender.
• The insert-placed rivers in the slot with the fourth side of the bottom. This section bar 20 * 20, length 375. In the bar is letkovyh two openings of different sizes. If the temperature is low, bees pass through the small gap and vice versa, and when the insert is removed completely medosbora.
• Supports hives height 90 mm are made on the same size, a bottom. The sides are cut at an angle 45 C. They attached prylёtnaya board, beveled for a snug fit to the body.

Multiple beehives napivramku

Some beekeepers in the Multiple keeping bee colonies used to hive napivramku.

In the case set frame size 435 mm * 145 mm and a thickness 10 mm.

Кількість рамок в корпусі – 10 pcs. Winter pidramnyy large space promotes good ventilation housing, This positive effect on family winter.

Advice! Stories of experienced beekeepers Multiple methods of keeping families with different design frames available on the forum beekeepers.

Keeping bees in hives Multiple

Multiple keeping bees allows work to expand the nest, adding, and removing the hive cases independently.

The construction of hives Multiple such, that their conduct pre-training: honeycombs filled with honey for, cells for the larvae, Wax.

When the body is released, it clean, conduct disinfection.

Nest during the season medosbora extend several buildings.

Перший – в between the main medosbora, другий – для prevent swarming.

Multiple third time expanding the hive during the productive trick, adding a third building housing.

With the end medosbora and wintering families to leave two buildings.

Multiple beehive Foam

Widely used now in Multiple beekeeping hive, made of foam.

This material has excellent insulating properties and maintains a constant temperature in the hive, summer does not overheat bees, winter protects them from the cold.

Easy to disinfect. Not rots from adverse weather, not grizetsya mice and does not let insects.

Keeping bees in hives Multiple foam has been used successfully in many modern apiaries in countries with high-tech beekeeping.